www.vishay.com for technical questions, contact: filmresistorsleaded@vishay.com document number: 28736 242 revision: 07-jul-10 cbb 0207 vishay beyschlag high pulse load carbon film leaded resistors cbb 0207 leaded resistors with advanced pulse load capability, are the perfect choice for circuitries exposed to high levels of electromagnetic interference or electrostatic discharge. the resistors can also be used to protect the circuitry of signal and mains input lines from surge pulses. applications are in all fields of automotive, telecommunication and industrial equipment. features ? speciality product for em c sensitive applications ? special carbon film technology for maximum heat stress capability ? up to 6 kv or 140 w pulse load capability ? resistance range: 10 to 1.5 m ? lead (pb)-free solder contacts ? pure tin plating provides compatibility with lead (pb)-free and lead containing soldering processes ? compliant to rohs directive 2002/95/ec applications ? automotive ? telecommunication ? industrial equipment note ? these resistors do not feature a limited li fetime when operated within the permissible limits. however, resistance value drift increasing over operating time may result in exceeding a li mit acceptable to the specific applicati on, thereby establishi ng a functional lifeti me. metric size din 0207 cecc b technical specifications description cbb 0207 cecc size b resistance range 10 to 1.5 m resistance tolerance 2 % temperature coefficient refer to temperature coefficient graph operation mode long term standard climatic category (lct/uct/days) 55/125/56 55/155/56 rated dissipation, p 70 0.4 w 0.6 w operating voltage, u max. ac/dc 350 v film temperature 125 c 155 c max. resistance change at p 70 for resistance range, r / r max., after: 10 to 100 k 1000 h 1 % 2 % 8000 h + 3 %/- 1 % + 5 %/- 2 % permissible voltage against ambient: 1 minute; u ins 500 v continuous 75 v failure rate: fit observed 0.1 x 10 - 9 /h
document number: 28736 for technical questions, contact: filmresistorsleaded@vishay.com www.vishay.com revision: 07-jul-10 243 cbb 0207 high pulse load carbon film leaded resistors vishay beyschlag dimensions notes (1) please refer to table packaging ? the part number is shown to facilitate the introduction of the unified part numbering system for ordering products note (1) resistance values to be selected from e24 series dimensions - leaded resistor types, mass and relevant physical dimensions type d max. (mm) l max. (mm) d nom. (mm) i min. (mm) m min. (mm) mass (mg) cbb 0207 2.5 6.3 0.6 28.0 10.0 220 part number and product description part number: CBB0207001501gc100 CBB0207001501gc1 p0 model/size variant tcr value tolerance pac k ag i n g (1) special CBB0207 0 = neutral 0 = standard see tcr graph 3 digit value 1 digit multiplier multiplier 7 = *10 - 3 2 = *10 2 8 = *10 - 2 3 = *10 3 9 = *10 - 1 4 = *10 4 0 = *10 0 5 = *10 5 1 = *10 1 6 = *10 6 g = 2 % ct c1 up to 2 digits 00 = standard product description: cbb 0207 2 % c1 1k5 cbb 0207 2 % c1 1k5 model size tolerance pac k ag i n g (1) resistance value cbb 0207 2 % ct c1 47k = 47 k 51r1 = 51.1 packaging model box pieces/box code cbb 0207 1000 5000 c1 ct tolerance and resistance range tolerance resistance value (1) cbb 0207 2 % 10 to 1.5 m l d d i i m
www.vishay.com for technical questions, contact: filmresistorsleaded@vishay.com document number: 28736 244 revision: 07-jul-10 cbb 0207 vishay beyschlag high pulse load carbon film leaded resistors description production is strictly controlled and follows an extensive set of instructions established for reproducibility. a homogeneous and dense carbon film is deposited on a high grade ceramic body (85 % al 2 o 3 ) and conditioned to achieve the desired temperature coefficient. nickel plated steel termination caps are firmly pressed on the rods. a special laser is used to achieve the target value by smoothly cutting a helical groove in the resistive layer without damaging the ceramics. connecting wires of electrolytic copper plated with 100 % pure tin are welded to the termination caps. the resistors are covered by protective coating designed for electrical, mechanical and climatic protection. five color code rings designate the resistance value and tolerance in accordance with iec 60062. the result of the determined production is verified by an extensive testing procedure performed on 100 % of the individual resistors. only accepted products are stuck directly on the adhesive tapes in accordance with iec 60286-1. assembly the resistors are suitable for processing on automatic insertion equipment and cutting and bending machines. excellent solderability is proven, even after extended storage. they are suitable for automatic soldering using wave or dipping. the encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. the suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. the resistors are completely lead (pb)-free, the pure tin plating provides co mpatibility with lead (pb)-free and lead-containing soldering processes. the immunity of the plating against tin whisker growth has been proven under extensive testing. all products comply with gadsl (1) and the cefic-eeca-eicta (2) list of legal restrictions on hazardous substances. this includes full compliance with the following directives: ? 2000/53/ec end of vehicle life directive (elv) and annex ii (elvii) ? 2002/95/ec restriction of the use of hazardous substances directive (rohs) ? 2002/96/ec waste electrical and electrical equipment directive (weee) approvals where applicable, the resistors are tested in accordance with en 140101-806 (successor of cecc 40101-806) which refers to en 60115-1 and en 140100. vishay beyschlag has achieved ?approval of manufacturer? in accordance with iec qc 001002-3, clause 2 . the release certificate for ?technology approval schedule? in accordance with cecc 240001 based on iec qc 001002-3, clause 6 is granted for the vishay beyschlag manu facturing process. notes (1) global automotive declar able substance list, see www.gadsl.org (2) cefic (european chemical industry council ), eeca (european electronic component manuf acturers association), eicta (european trade organisation repres enting the information and communications te chnology and consumer electronics), see www.eicta.org/index.php?id=1053&id_article=340 functional description c 100 150 0 - 50 0 50 0.5 1 w 70 ambient temperature amb ? power dissipation p cbb 0207 derating - standard operation
document number: 28736 for technical questions, contact: filmresistorsleaded@vishay.com www.vishay.com revision: 07-jul-10 245 cbb 0207 high pulse load carbon film leaded resistors vishay beyschlag 100 150 0 - 50 0 50 0.5 1 w 70 ambient temperature amb ? power dissipation p c cbb 0207 derating - long term operating cbb 0207 0 20 60 0.7 40 8 0 k temperature rise t r 0 0.1 0.2 0.3 0.4 0.5 0.6 0. 8 0.9 1 1.1 1.2 w load p temperature rise 100 s 1 ms 10 ms 1 1 s 10 s 0.1 w 10 s 100 ms 10 100 pulse duration t i pulse load p max. cbb 0207 maximum pulse load, single pulse; for permissibl e resistance change equivalent to 8000 h operation. single pulse
www.vishay.com for technical questions, contact: filmresistorsleaded@vishay.com document number: 28736 246 revision: 07-jul-10 cbb 0207 vishay beyschlag high pulse load carbon film leaded resistors 100 s 1 ms 10 ms 1 1 s 10 s 0.1 w 10 s 100 ms 10 100 pulse duration t i continuous pulse load p max. cbb 0207 maximum pulse load, continuous pul ses; for permissible resistance change equivalent to 8000 h operation. continuous pulse 100 s 1 ms 10 ms 1 s 10 s 1 kv 100 v 10 s 100 ms pulse duration t i pulse volta g e u max. cbb 0207 maximum pulse voltage, single and continuous pulses; for per missible resistance change equivalent to 8000 h operation. pulse voltage 100 v 1 kv 10 v 10 kv 100 1 k 10 k 100 k 10 10 m resistance value r 1 m cbb 0207 test volta g e 1.2/50 s pulse load rating in accordance with iec 60115-1, 4.27; 1.2 s/50 s; 5 pulses at 12 s intervals; for permissible resistance change 0.5 %. 1.2/50 pulse
document number: 28736 for technical questions, contact: filmresistorsleaded@vishay.com www.vishay.com revision: 07-jul-10 247 cbb 0207 high pulse load carbon film leaded resistors vishay beyschlag 100 v 1 kv 10 v 10 kv 100 1 k 10 k 100 k 10 10 m resistance value r test volta g e 10/700 s 1 m cbb 0207 pulse load rating in accor dance with iec 60115-1, 4.27; 10 s/ 700 s; 10 pulses at 1 minute intervals; for permissible resistance change 0.5 %. 10/700 pulse - 500 ppm/k - 400 - 300 - 200 - 100 100 1 k 10 k 100 k 10 10 m resistance value r temperature coefficient (tcr) 1 m cbb 0207 temperature coefficient (tcr) 0.01 0.1 1 v/v 10 m 10 k 100 k 1 k 1 m resistance value r current noise a 1 cbb 0207 current noise - a 1 in accordance with iec 60195
www.vishay.com for technical questions, contact: filmresistorsleaded@vishay.com document number: 28736 248 revision: 07-jul-10 cbb 0207 vishay beyschlag high pulse load carbon film leaded resistors tests and requirements essentially all tests are carried out in accordance with the following specifications: en 60115-1, generic specification (includes tests) en 140100, sectional specification (includes schedule for qualification approval) en 140101-806 (successor of cecc 40101-806), detail specification (includes schedul e for conformance inspection) the following table contains the applicable tests selected from the documents listed above. the tests are carried out in accordance with iec 60068-2-xx test method and under standard atmospheric conditions in accordance with iec 60068-1, 5.3. climatic category lct/uct/56 (rated temperatur e range: lower category temperature, upper category temperature; damp heat, long term, 56 days) is valid. unless otherwise specified the following values apply: temperature: 15 c to 35 c relative humidity: 45 % to 75 % air pressure: 86 kpa to 106 kpa (860 mbar to 1060 mbar). in the test procedures and requirements table only the tests and requirements are listed with reference to the relevant clauses of iec 60115-1 and iec 60068-2-xx test methods. a short description of the test procedure is also given. test procedures and requirements iec 60115-1 clause iec 60068-2-xx test method test procedure requirements permissible change ( r ) stability for product types: cbb 0207 10 to 1.5 m 4.5 - resistance 2 % 4.8 - temperature coefficient at (20/lct/20) c and (20/uct/20) c - 4.25.1 - endurance at 70 c: standard operation mode u = or u = u max. ; 1.5 h on; 0.5 h off 70 c; 1000 h (2 % r + 0.05 ) 70 c; 8000 h (4 % r + 0.05 ) 4.25.1 - endurance at 70 c: long term operation mode u = or u = u max. ; 1.5 h on; 0.5 h off 70 c; 1000 h (1 % r + 0.05 ) 70 c; 8000 h (2 % r + 0.05 ) 4.25.3 - endurance at upper category temperature 125 c; 1000 h (2 % r + 0.05 ) 155 c; 1000 h (4 % r +0.1 ) 4.24 78 (cab) damp heat, steady state (40 2) c; 56 days; (93 3) % rh (1 % r +0.1 ) 4.23 climatic sequence: 4.23.2 2 (ba) dry heat 155 c; 16 h 4.23.3 30 (db) damp heat, cyclic 55 c; 24 h; 90 % to 100 % rh; 1 cycle 4.23.4 1 (aa) cold - 55 c; 2 h 4.23.5 13 (m) low air pressure 8.5 kpa; 2 h; 15 c to 35 c 4.23.6 30 (db) damp heat, cyclic 55 c; 5 days; 95 % to 100 % rh; 5 cycles (1 % r +0.1 ) no visible damage - 1 (aa) cold - 55 c; 2 h (0.5 % r +0.1 ) 4.13 - short time overload room temperature; u = 2.5 x or u = 2 x u max. ; 5 s (0.5 % r +0.1 ) no visible damage p 70 x r p 70 x r p 70 x r
document number: 28736 for technical questions, contact: filmresistorsleaded@vishay.com www.vishay.com revision: 07-jul-10 249 cbb 0207 high pulse load carbon film leaded resistors vishay beyschlag historical 12nc information ? the resistors had a 12-digit numeric code starting with 2312. ? the subsequent 4 digits indicated the resistor type, specification and packaging; see the 12nc table. ? the remaining 4 digits indica ted the resistance value: - the first 3 digits indicated the resistance value. - the last digit indicated the resistance decade in accordance with the resistance decade table. resistance decade 12nc example the 12nc of a cbb 0207 resistor, value 47 k with 2 % tolerance, supplied on bandolier in a box of 5000 units was: 2312 955 24703. 4.19 14 (na) rapid change of temperature 30 min at lct = - 55 c and 30 min at uct = 155 c; 200 cycles (0.5 % r + 0.05 ) no visible damage 4.29 45 (xa) component solvent resistance isopropyl alcohol + 23 c; toothbrush method marking legible; no visible damage 4.18.2 20 (tb) resistance to soldering heat unmounted components; (260 3) c; (10 1) s (0.5 % r + 0.05 ) no visible damage 4.17 20 (ta) solderability + 235 c; 2 s solder bath method snpb40 good tinning ( 95 % covered, no visible damage) + 245 c; 3 s solder bath method snag3cu0.5 4.22 6 (b4) vibration 6 h; 10 hz to 2000 hz 1.5 mm or 196 m/s 2 (0.5 % r + 0.05 ) 4.16 21 (ua 1 ) 21 (ub) 21 (uc) robustness of terminations tensil, bending and torsion (0.5 % r + 0.05 ) 4.7 - voltage proof u rms = u ins ; 60 s no flashover or breakdown 4.40 - electrostatic discharge (human body model) iec 61340-3-1; 3 pos. + 3 neg. 16 kv (0.5 % r + 0.05 ) test procedures and requirements iec 60115-1 clause iec 60068-2-xx test method test procedure requirements permissible change ( r ) stability for product types: cbb 0207 10 to 1.5 m resistance decade last digit 10 to 99.9 9 100 to 999 1 1 k to 9.99 k 2 10 k to 99.9 k 3 100 k to 999 k 4 1m to 9.99 m 5 historical 12nc - resistor type and packaging description 2312 ... ..... bandolier in box type tol. c1 1000 units ct 5000 units cbb 0207 2 % 950 2.... 955 2....
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu.
|
